New Head Stud Kit For Ford 08-10 Powerstroke 6.4L Diesel 250-4203 GLOBAL

Description

How to get Discount?
Add This Item to Your Watchlist, Meanwhile Save this Seller to Your Favs, Get Discount Message Future.
Questions? Contact us!
Fits Ford 6.4 Liter Powerstroke Turbo Diesel
2008 Through 2010 Ford Trucks And SUVs
Part number 250-4203
Includes All Necessary Studs Nuts And Washers To Replace Your Factory Head Bolts On BOTH Heads Includes assembly Lubricant
Stud uses a premium grade 8740 chromoly. Then, each stud is placed vertically in special racks and precisely heat-treated to 220,000 psi. This procedure ensures complete heat penetration and the results are far superior to those lesser quality studs from other manufacturers who just dump pieces in a basket and hope for the best.
Following heat-treat, each stud is center-less ground to make it as close to perfectly concentric as possible. This procedure involves about ten very slight cuts and results in an exceptionally straight part. It s important to note that lesser quality studs are not even center-less ground the material is thread rolled in bar stock form (mostly before heat-treat, when the material is easier to machine). Because our studs are manufactured to such exacting tolerances, you will note that gaskets and cylinder heads literally glide into position and are perfectly aligned something that won t happen with inferior quality head studs. our studs are thread rolled after heat-treat, which gives them about 1000% (thats ten times) better fatigue strength than those studs that are threaded prior to heat-treat (a very common industry practice).
FITS:
2010 Ford F-250 Super Duty 6.4L V8 DIESEL
2010 Ford F-350 Super Duty 6.4L V8 DIESEL
2010 Ford F-450 Super Duty 6.4L V8 DIESEL
2010 Ford F-550 Super Duty 6.4L V8 DIESEL
2009 Ford F-250 Super Duty 6.4L V8 DIESEL
2009 Ford F-350 Super Duty 6.4L V8 DIESEL
2009 Ford F-450 Super Duty 6.4L V8 DIESEL
2009 Ford F-550 Super Duty 6.4L V8 DIESEL
2008 Ford F-250 Super Duty 6.4L V8 DIESEL
2008 Ford F-350 Super Duty 6.4L V8 DIESEL
2008 Ford F-450 Super Duty 6.4L V8 DIESEL All
2008 Ford F-550 Super Duty 6.4L V8 DIESEL All
2007 Ford F-250 Super Duty 6.4L V8 DIESEL All
2007 Ford F-350 Super Duty 6.4L V8 DIESEL
2007 Ford F-450 Super Duty 6.4L V8 DIESEL All
2007 Ford F-550 Super Duty 6.4L V8 DIESEL All
2010 Ford F-550 Super Duty Lariat Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2010 Ford F-550 Super Duty Lariat Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2010 Ford F-550 Super Duty XL Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2010 Ford F-550 Super Duty XL Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2010 Ford F-550 Super Duty XLT Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2010 Ford F-550 Super Duty XLT Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-250 Super Duty Cabela's Crew Cab Pickup 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty Lariat Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty Lariat Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty XL Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty XL Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty XLT Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2009 Ford F-550 Super Duty XLT Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty Lariat Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty Lariat Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty XL Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty XL Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty XLT Cab & Chassis 2-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
2008 Ford F-550 Super Duty XLT Cab & Chassis 4-Door 6.4L 391Cu. In. V8 DIESEL OHV Turbocharged
INSTALLATION METHOD FOR HEAD STUD KITS
1. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit, length and dimension.
2. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if necessary with a Thread Chaser.
3. Screw studs into the block “
HAND TIGHT ONLY
”
.
NOTE: LOCTITE MAY BE USED IF A PERMANENT MOUNTING OF THE STUDS IS PREFERRED. THE FASTENERS, HOWEVER, MUST BE TORQUED PRIOR TO THE LOCTITE SETTING UP.
PRELOAD (TORQUE) RECOMMENDATIONS
Following the manufacturers recommended torque sequence tighten the nuts to the following specifications with ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Step 1. Tighten studs 1 thru 10 to
90
ft-lbs.
Step 2. Tighten studs 1 thru 10 to
180
ft-lbs.
Step 3.
Final tighten studs 1 thru 10 to
275
ft-lbs
.
Step 4. Tighten M8 bolts 11 thru 15 to
25
ft-lbs.
Bolt Torque Sequence
Not what you were looking for? Search our
Store Page
to find the right part!
Warranty:
In the Warranty this item should fail due to manufacturing defects during intended use, we will replace the part free of charge (excludes shipping charges) for the original purchaser.
We only warranty cost of parts. Any installation or other fees are non-refundable.
If a part arrives damaged, or is defective, it is our responsibility to take care of it but it must be reported to us immediately.
Please note: Any modifications to an item of any kind before contacting us will void any and all warranty coverage for this item. Please contact us before modifying the part so that we have the opportunity to correct the situation.
Manufacturer Information
● Products are manufactured in ISO 9000 / 9001 / 9002 certified facilities.
● Products go through multiple inspection processes: Durability Test Platform, Performance Test Platform, High&Low Temperature Fatigue Test Platform, Products Lifetime Test Platform, Multipurpose Numeric Display Hydraulic Pressure Test Machine, Metallographic Detection Device, Salt Spray Test Machine, Spring Tension & Compression Test Machine, Swing Machine, Rockwell Hardness Tester, Brinell Hardness Tester, Shore Hardness Tester, Contourgraph Measuring Machine, Torque Testing Online.
● R & D Team develop new item with 3D Scanner, UG ,PRO/E and AutoCAD
GREASE FITTINGS
● All of our parts had been pre-greased already, no matter greasable or sealed. It means it's need not to grease the parts again, otherwise, the grease will overflow.
● Some of the parts we sell have grease fittings, other parts come factory sealed. This does not affect the performance or quality of the parts. Due to volume of sales we cannot guarantee which type you will receive.
DELIVERY DETAILS
● Monday-Friday(excluding weekend and holidays)tracking number will be provided once items are shipped.
● Normally the package will be delivered within 3-5 business days.
● If don't receive your item within 10 days, pls contact us immediately, we will do our best to press the shipment company to send it fast.
PAYMENT
Please use the eBay checkout system when paying for your order.
Immediate payment is required for all orders.
RERURN POLICY
Customer must contact us within 30 days of receiving shipment for approval of any return or exchange. Returns or exchanges will be subject to a 15% restocking fee of the original item purchased, plus cost of replacement shipping. Exchanges due to shipping errors by us will not be subject to a restocking fee or shipping charges.
On Jun-10-21 at 01:26:19 PDT, seller added the following information: